View AK4359_274465.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

ASAHI KASEI
[AK4359]
AK4359
192kHz 24-Bit 8ch DAC
GENERAL DESCRIPTION The AK4359 is eight channels 24bit DAC corresponding to digital audio system. Using AKM's advanced multi bit architecture for its modulator the AK4359 delivers a wide dynamic range while preserving linearity for improved THD+N performance. The AK4359 has single end SCF outputs, increasing performance for systems with excessive clock jitter. The AK4359 accepts 192kHz PCM data, ideal for a wide range of applications including DVD-Audio. FEATURES Sampling Rate Ranging from 8kHz to 192kHz 24Bit 8 times Digital Filter with Slow roll-off option THD+N: -94dB DR, S/N: 106dB High Tolerance to Clock Jitter Single Ended Output Buffer with 2nd order Analog LPF Digital De-emphasis for 32, 44.1 & 48kHz sampling Zero Detect function Channel Independent Digital Attenuator (Linear 256 steps) 3-wire Serial and I2C Bus P I/F for mode setting 2 I/F format: MSB justified, LSB justified (16bit, 20bit, 24bit), I S, TDM Master clock: 256fs, 384fs, 512fs or 768fs or 1152fs (Normal Speed Mode) 128fs, 192fs, 256fs or 384fs (Double Speed Mode) 128fs or 192fs (Quad Speed Mode) Power Supply: 4.5 to 5.5V 30pin VSOP Package
DZF LOUT1
Audio I/F LPF SCF DAC DATT
ROUT1
LPF
SCF
DAC
DATT
PCM
LOUT2
LPF
SCF
DAC
DATT Control Register
MCLK LRCK BICK SDTI1 SDTI2 SDTI3 SDTI4
3-wire or I2C
ROUT2
LPF
SCF
DAC
DATT
LOUT3
LPF
SCF
DAC
DATT
ROUT3
LPF LPF
SCF SCF
DAC DAC
DATT DATT
LOUT4
ROUT4
LPF
SCF
DAC
DATT
AK4359
MS0289-E-00 -1-
2004/02
ASAHI KASEI
[AK4359]
Ordering Guide
AK4359VF AKD4359 -40 +85C 30pin VSOP Evaluation Board for AK4359
Pin Layout
MCLK BICK SDTI1 LRCK RSTB SMUTE/CSN/CAD0 ACKS/CCLK/SCL DIF0/CDTI/SDA SDTI2 SDTI3 SDTI4 DIF1 DEM0 DVDD DVSS
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
30 29 28 27 26
DZF1 DZF2 AVDD AVSS VCOM LOUT1 ROUT1 P/S LOUT2 ROUT2 LOUT3 ROUT3 LOUT4 ROUT4 DEM1/I2C
AK4359 Top View
25 24 23 22 21 20 19 18 17 16
MS0289-E-00 -2-
2004/02
ASAHI KASEI
[AK4359]
Compatibility with AK4384
1. Function Functions # of channels I2C DEM control 16/20bit LSB justified format control 2. Pin Configuration AK4359 MCLK BICK SDTI1 LRCK RSTB SMUTE/CSN/CAD0 ACKS/CCLK/SCL DIF0/CDTI/SDA SDTI2 SDTI3 SDTI4 DIF1 DEM0 DVDD DVSS 3. Register map Addr 00H 01H 02H 03H 04H 05H 06H 07H 08H 09H 0AH 0BH 0CH 0DH 0EH Register Name Control 1 Control 2 Control 3 LOUT1 ATT Control ROUT1 ATT Control LOUT2 ATT Control ROUT2 ATT Control LOUT3 ATT Control ROUT3 ATT Control LOUT4 ATT Control ROUT4 ATT Control Invert Output Signal DZF1 Control DZF2 Control DEM Control D7 ACKS 0 PW4 ATT7 ATT7 ATT7 ATT7 ATT7 ATT7 ATT7 ATT7 INVL1 L1 L1 0 D6 D5 D4 D3 TDM1 TDM0 DIF2 DIF1 0 SLOW DFS1 DFS0 PW3 PW2 0 0 ATT6 ATT5 ATT4 ATT3 ATT6 ATT5 ATT4 ATT3 ATT6 ATT5 ATT4 ATT3 ATT6 ATT5 ATT4 ATT3 ATT6 ATT5 ATT4 ATT3 ATT6 ATT5 ATT4 ATT3 ATT6 ATT5 ATT4 ATT3 ATT6 ATT5 ATT4 ATT3 INVR1 INVL2 INVR2 INVL3 R1 L2 R2 L3 R1 L2 R2 L3 0 0 0 DEMA : Compatible with AK4384's register. D2 DIF0 DEM1 DZFB ATT2 ATT2 ATT2 ATT2 ATT2 ATT2 ATT2 ATT2 INVR3 R3 R3 DEMB D1 PW1 DEM0 0 ATT1 ATT1 ATT1 ATT1 ATT1 ATT1 ATT1 ATT1 INVL4 L4 L4 DEMC D0 RSTN SMUTE 0 ATT0 ATT0 ATT0 ATT0 ATT0 ATT0 ATT0 ATT0 INVR4 R4 R4 DEMD AK4384 MCLK BICK SDTI LRCK PDN SMUTE/CSN ACKS/CCLK DIF0/CDTI Pin# 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Pin# 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 AK4384 DZFL DZFR VDD VSS VCOM AOUTL AOUTR P/S AK4359 DZF1 DZF2 AVDD AVSS VCOM LOUT1 ROUT1 P/S LOUT2 ROUT2 LOUT3 ROUT3 LOUT4 ROUT4 I2C/DEM1 AK4384 2 Not available Register Register AK4359 8 Available Pin/Register Pin/Register
MS0289-E-00 -3-
2004/02
ASAHI KASEI
[AK4359]
PIN/FUNCTION
Function Master Clock Input Pin An external TTL clock should be input on this pin. 2 BICK I Audio Serial Data Clock Pin 3 SDTI1 I DAC1 Audio Serial Data Input Pin 4 LRCK I L/R Clock Pin 5 RSTB I Reset Mode Pin When at "L", the AK4359 is in the reset mode. The AK4359 should always be reset upon power-up. 6 SMUTE I Soft Mute Pin in parallel mode "H": Enable, "L": Disable CSN I Chip Select Pin in serial 3-wire mode CAD0 I Chip Address Pin in serial I2C mode 7 ACKS I Auto Setting Mode Pin in parallel mode "L": Manual Setting Mode, "H": Auto Setting Mode CCLK I Control Data Clock Pin in serial 3-wire mode SCL Control Data Clock Pin in serial I2C mode 8 DIF0 I Audio Data Interface Format Pin in parallel mode CDTI I Control Data Input Pin in serial 3-wire mode SDA I/O Control Data Pin in serial I2C mode 9 SDTI2 I DAC2 Audio Serial Data Input Pin 10 SDTI3 I DAC3 Audio Serial Data Input Pin 11 SDTI4 I DAC4 Audio Serial Data Input Pin 12 DIF1 I Audio Data Interface Format Pin 13 DEM0 I De-emphasis Filter Enable Pin 14 DVDD Digital Power Supply Pin, +4.5+5.5V 15 DVSS Digital Ground Pin 16 I2C I Control Mode Select Pin in serial mode "L": 3-wire Serial, "H": I2C Bus DEM1 I De-emphasis Filter Enable Pin in parallel mode 17 ROUT4 O DAC4 Rch Analog Output Pin 18 LOUT4 O DAC4 Rch Analog Output Pin 19 ROUT3 O DAC3 Rch Analog Output Pin 20 LOUT3 O DAC3 Rch Analog Output Pin 21 ROUT2 O DAC2 Rch Analog Output Pin 22 LOUT2 O DAC2 Rch Analog Output Pin 23 P/S I Parallel/Serial Select Pin (Internal pull-up pin) "L": Serial control mode, "H": Parallel control mode 24 ROUT1 O DAC1 Rch Analog Output Pin 25 LOUT1 O DAC1 Lch Analog Output Pin 26 VCOM O Common Voltage Pin, AVDD/2 Normally connected to AVSS with a 0.1F ceramic capacitor in parallel with a 10F electrolytic cap. 27 AVSS Analog Ground Pin 28 AVDD Analog Power Supply Pin, +4.5+5.5V 29 DZF2 O Data Zero Input Detect Pin 30 DZF1 O Data Zero Input Detect Pin Note: All input pins except pull-up pin should not be left floating. No. 1 Pin Name MCLK I/O I
MS0289-E-00 -4-
2004/02
ASAHI KASEI
[AK4359]
Handling of Unused Pin
The unused I/O pins should be processed appropriately as below. Classification Analog Digital Pin Name LOUT4-1, ROUT4-1 DZF2-1 SDTI4-1, SMUTE, DIF1, DEM0 Setting These pins should be open. These pins should be open. These pins should be connected to DVSS.
ABSOLUTE MAXIMUM RATINGS (AVSS, DVSS=0V; Note 1) Parameter Symbol Min Power Supplies Analog AVDD -0.3 Digital DVDD -0.3 |AVSS-DVSS| (Note 2) GND Input Current (any pins except for supplies) IIN Analog Input Voltage VINA -0.3 Digital Input Voltage VIND -0.3 Ambient Operating Temperature Ta -40 Storage Temperature Tstg -65
Note 1. All voltages with respect to ground. Note 2. AVSS and DVSS must be connected to the same analog ground plane.
Max 6.0 6.0 0.3 10 AVDD+0.3 DVDD+0.3 85 150
Units V V V mA V V C C
WARNING: Operation at or beyond these limits may result in permanent damage to the device. Normal operation is not guaranteed at these extremes.
RECOMMENDED OPERATING CONDITIONS (AVSS, DVSS=0V; Note 1) Parameter Symbol Min Typ Power Supplies Analog AVDD 4.5 5.0 (Note 3) Digital DVDD 4.5 5.0
Note 3. The power up sequence between AVDD and DVDD is not critical. *AKM assumes no responsibility for the usage beyond the conditions in this datasheet.
Max 5.5 5.5
Units V V
MS0289-E-00 -5-
2004/02
ASAHI KASEI
[AK4359]
ANALOG CHARACTERISTICS (Ta=25C; AVDD, DVDD=5V; VREFH=AVDD; fs=44.1kHz; BICK=64fs; Signal Frequency=1kHz; 24bit Input Data; Measurement frequency=20Hz 20kHz; RL 5k; unless otherwise specified) Parameter Min Typ Max Units Resolution 24 Bits Dynamic Characteristics (Note 4) THD+N Fs=44.1kHz 0dBFS -94 -84 dB BW=20kHz -60dBFS -42 dB fs=96kHz 0dBFS -92 dB BW=40kHz -60dBFS -39 dB fs=192kHz 0dBFS -92 dB BW=40kHz -60dBFS -39 dB Dynamic Range (-60dBFS with A-weighted) (Note 5) 98 106 dB S/N (A-weighted) (Note 6) 98 106 dB Interchannel Isolation (1kHz) 90 100 dB Interchannel Gain Mismatch 0.2 0.5 dB DC Accuracy Gain Drift 100 ppm/C Output Voltage (Note 7) 3.15 3.4 3.65 Vpp Load Resistance (Note 8) 5 k Power Supplies Power Supply Current (AVDD+DVDD) 55 85 mA Normal Operation (RSTB pin = "H", fs96kHz) 63 90 mA Normal Operation (RSTB pin = "H", fs=192kHz) 60 150 Reset Mode (RSTB pin = "L") (Note 9) A
Note 4. Measured by Audio Precision System Two. Refer to the evaluation board manual. Note 5. 100dB at 16bit data. Note 6. S/N does not depend on input bit length. Note 7. Full scale voltage (0dB). Output voltage scales with the voltage of AVDD pin. AOUT (typ. @0dB) = 3.4VppxAVDD/5.0 Note 8. For AC-load. Note 9 All digital input pins including clock pins (MCLK, BICK, LRCK) are held DVSS.
MS0289-E-00 -6-
2004/02
ASAHI KASEI
[AK4359]
SHARP ROLL-OFF FILTER CHARACTERISTICS (Ta = 25C; AVDD, DVDD = 4.5 5.5V; fs = 44.1kHz; DEM = OFF; SLOW = "0") Parameter Symbol Min Typ Digital filter PB 0 Passband 0.05dB (Note 10) 22.05 -6.0dB Stopband (Note 10) SB 24.1 Passband Ripple PR Stopband Attenuation SA 54 Group Delay (Note 11) GD 19.3 Digital Filter + SCF Frequency Response 20.0kHz Fs=44.1kHz FR + 0.06/-0.10 40.0kHz Fs=96kHz FR + 0.06/-0.13 80.0kHz Fs=192kHz FR + 0.06/-0.51
Max 20.0 0.02 -
Units kHz kHz kHz dB dB 1/fs dB dB dB
Note 10. The passband and stopband frequencies scale with fs(system sampling rate). For example, PB=0.4535xfs (@0.05dB), SB=0.546xfs. Note 11. The calculating delay time which occurred by digital filtering. This time is from setting the 16/24bit data of both channels to input register to the output of analog signal.
SLOW ROLL-OFF FILTER CHARACTERISTICS (Ta = 25C; AVDD, DVDD = 4.5~5.5V; fs = 44.1kHz; DEM = OFF; SLOW = "1")
Parameter Digital Filter Passband 0.04dB -3.0dB (Note 12) (Note 12) PB SB PR SA GD FR FR FR 0 39.2 72 18.2 8.1 0.005 19.3 +0.1/-4.3 +0.1/-3.3 +0.1/-3.7 kHz kHz kHz dB dB 1/fs dB dB dB Symbol Min Typ Max Units
Stopband Passband Ripple Stopband Attenuation Group Delay Digital Filter + SCF Frequency Response
(Note 11) 20.0kHz 40.0kHz 80.0kHz fs=44.kHz fs=96kHz fs=192kHz
Note 12. The passband and stopband frequencies scale with fs. For example, PB = 0.185xfs (@0.04dB), SB = 0.888xfs.
DC CHARACTERISTICS (Ta = 25C; AVDD, DVDD = 4.5 5.5V) Parameter Symbol Min High-Level Input Voltage VIH 2.2 Low-Level Input Voltage VIL High-Level Output Voltage (Iout = -80A) VOH DVDD-0.4 Low-Level Output Voltage (Iout = 80A) VOL Input Leakage Current (Note 13) Iin Note 13. P/S pin has internal pull-up device, nominally 100k.
Typ -
Max 0.8 0.4 10
Units V V V V A
MS0289-E-00 -7-
2004/02
ASAHI KASEI
[AK4359]
SWITCHING CHARACTERISTICS (Ta = 25C; AVDD, DVDD = 4.5 5.5V; CL = 20pF) Parameter Symbol Min fCLK 2.048 Master Clock Frequency Duty Cycle dCLK 40 LRCK Frequency
Normal Mode (TDM0= "0", TDM1= "0") Normal Speed Mode Double Speed Mode Quad Speed Mode Duty Cycle TDM256 mode (TDM0= "1", TDM1= "0") Normal Speed Mode High time Low time TDM128 mode (TDM0= "1", TDM1= "1") Normal Speed Mode Double Speed Mode High time Low time Audio Interface Timing BICK Period BICK Pulse Width Low Pulse Width High BICK "" to LRCK Edge (Note 14, 15) LRCK Edge to BICK "" (Note 14, 15) SDTI Hold Time SDTI Setup Time Control Interface Timing (3-wire Serial mode): CCLK Period CCLK Pulse Width Low Pulse Width High CDTI Setup Time CDTI Hold Time CSN High Time CSN "" to CCLK "" CCLK "" to CSN "" Control Interface Timing (I2C Bus mode): (Note 18) SCL Clock Frequency Bus Free Time Between Transmissions Start Condition Hold Time (prior to first clock pulse) Clock Low Time Clock High Time Setup Time for Repeated Start Condition SDA Hold Time from SCL Falling (Note 16) SDA Setup Time from SCL Rising Rise Time of Both SDA and SCL Lines (Note 17) Fall Time of Both SDA and SCL Lines (Note 17) Setup Time for Stop Condition Pulse Width of Spike Noise Suppressed by Input Filter fsn fsd fsq Duty fsn tLRH tLRL fsn fsd tLRH tLRL tBCK tBCKL tBCKH tBLR tLRB tSDH tSDS tCCK tCCKL tCCKH tCDS tCDH tCSW tCSS tCSH fSCL tBUF tHD:STA tLOW tHIGH tSU:STA tHD:DAT tSU:DAT tR tF tSU:STO tSP 8 60 120 45 8 1/256fs 1/256fs 8 60 1/128fs 1/128fs 81 30 30 20 20 10 10 200 80 80 40 40 150 50 50 1.3 0.6 1.3 0.6 0.6 0 0.1 0.6 0
Typ 11.2896
Max 36.864 60
Units MHz %
48 96 192 55 48
kHz kHz kHz % kHz ns ns kHz kHz ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns
48 96
400 0.3 0.3 50
kHz s s s s s s s s s s ns
MS0289-E-00 -8-
2004/02
ASAHI KASEI
[AK4359]
Parameter Reset Timing RSTB Pulse Width
Symbol (Note 18) tRST
Min 150
Typ
Max
Units ns
Note 14. BICK rising edge must not occur at the same time as LRCK edge. Note 15. This spec is required input signal. Note 16. Data must be held for sufficient time to bridge the 300 ns transition time of SCL. Note 17 This spec is required input signal. Note 18. The AK4359 can be reset by bringing RSTB pin = "L". Note 19. I2C is a registered trademark of Philips Semiconductors.
Purchase of Asahi Kasei Microsystems Co., Ltd I2C components conveys a license under the Philips I2C patent to use the components in the I2C system, provided the system conform to the I2C specifications defined by Philips.
MS0289-E-00 -9-
2004/02
ASAHI KASEI
[AK4359]
Timing Diagram
1/fCLK VIH VIL tCLKH tCLKL
dCLK=tCLKH x fCLK, tCLKL x fCLK
MCLK
1/fs VIH VIL
LRCK
tBCK VIH VIL tBCKH tBCKL
BICK
Clock Timing
LRCK tBLR tLRB
VIH VIL
BICK tSDS tSDH
VIH VIL
SDTI
VIH VIL
Audio Serial Interface Timing
MS0289-E-00 - 10 -
2004/02
ASAHI KASEI
[AK4359]
VIH CSN VIL tCSS tCCKL tCCKH VIH VIL tCDS tCDH VIH VIL
CCLK
CDTI
C1
C0
R/W
A4
WRITE Command Input Timing
tCSW VIH CSN VIL tCSH CCLK VIH VIL
VIH CDTI D3 D2 D1 D0 VIL
WRITE Data Input Timing
VIH SDA VIL tBUF tLOW tR tHIGH tF tSP VIH SCL VIL tHD:STA Stop Start tHD:DAT tSU:DAT tSU:STA Start tSU:STO Stop
I2C Bus mode Timing
tRST
RSTB
VIL
Reset Timing MS0289-E-00 - 11 2004/02
ASAHI KASEI
[AK4359]
OPERATION OVERVIEW System Clock
The external clocks, which are required to operate the AK4359, are MCLK, LRCK and BICK. The master clock (MCLK) should be synchronized with LRCK but the phase is not critical. The MCLK is used to operate the digital interpolation filter and the delta-sigma modulator. There are two methods to set MCLK frequency. In Manual Setting Mode (ACKS bit = "0": Register 00H), the sampling speed is set by DFS0-1 (Table 1). The frequency of MCLK at each sampling speed is set automatically. (Table 2~Table 4) In Auto Setting Mode (ACKS bit = "1": Default), as MCLK frequency is detected automatically (Table 5), and the internal master clock becomes the appropriate frequency (Table 6), it is not necessary to set DFS0-1. In parallel mode, the sampling speed can be set by only ACKS pin. Both DFS0 and DFS1 are fixed to "0". When ACKS pin = "L", the AK4359 operates by Normal Speed Mode. When ACKS pin = "H", Auto setting mode is enabled. The parallel mode does not support 128fs and 192fs of Double Speed Mode. All external clocks (MCLK, BICK and LRCK) should always be present whenever the AK4359 is in the normal operation mode (RSTB pin = "H"). If these clocks are not provided, the AK4359 may draw excess current and may fall into unpredictable operation. This is because the device utilizes dynamic refreshed logic internally. The AK4359 should be reset by RSTB pin = "L" after threse clocks are provided. If the external clocks are not present, the AK4359 should be in the power-down mode (RSTB pin = "L"). After exiting reset(RSTB = "") at power-up etc., the AK4359 is in the power-down mode until MCLK is input. DFS1 0 0 1 DFS0 0 1 0 Sampling Rate (fs) Normal Speed Mode Double Speed Mode Quad Speed Mode 8kHz~48kHz 60kHz~96kHz 120kHz~192kHz Default
Table 1. Sampling Speed (Manual Setting Mode) LRCK fs 32.0kHz 44.1kHz 48.0kHz MCLK 512fs 16.3840MHz 22.5792MHz 24.5760MHz BICK 64fs 2.0480MHz 2.8224MHz 3.0720MHz
256fs 8.1920MHz 11.2896MHz 12.2880MHz
384fs 12.2880MHz 16.9344MHz 18.4320MHz
768fs 24.5760MHz 33.8688MHz 36.8640MHz
1152fs 36.8640MHz N/A N/A
Table 2. System Clock Example (Normal Speed Mode @Manual Setting Mode)
MS0289-E-00 - 12 -
2004/02
ASAHI KASEI
[AK4359]
LRCK fs 88.2kHz 96.0kHz
128fs 106896MHz 12.2880MHz
MCLK 192fs 256fs 16.9344MHz 22.5792MHz 18.4320MHz 24.5760MHz
384fs 33.8688MHz 36.8640MHz
BICK 64fs 5.6448MHz 6.1440MHz
Table 3. System Clock Example (Double Speed Mode @Manual Setting Mode) LRCK fs 176.4kHz 192.0kHz MCLK 128fs 192fs 22.5792MHz 33.8688MHz 24.5760MHz 36.8640MHz BICK 64fs 106896MHz 12.2880MHz
Table 4. System Clock Example (Quad Speed Mode @Manual Setting Mode) MCLK 512fs 768fs 256fs 384fs 128fs 192fs Sampling Speed Normal Double Quad
Table 5. Sampling Speed (Auto Setting Mode) LRCK fs 32.0kHz 44.1kHz 48.0kHz 88.2kHz 96.0kHz 176.4kHz 192.0kHz MCLK (MHz) 384fs 512fs 16.3840 22.5792 24.5760 33.8688 36.8640 Sampling Speed Normal Double Quad
128fs 22.5792 24.5760
192fs 33.8688 36.8640
256fs 22.5792 24.5760 -
768fs 24.5760 33.8688 36.8640 -
1152fs 36.8640 -
Table 6. System Clock Example (Auto Setting Mode)
MS0289-E-00 - 13 -
2004/02
ASAHI KASEI
[AK4359]
Audio Serial Interface Format
In parallel mode, the DIF0-1 pins as shown in Table 7 can select four serial data modes. In serial mode, the DIF0-2 bits s shown in Table 8 can select five serial data modes. Initial value of DIF0-2 bits is "010". In all modes the serial data is MSB-first, 2's complement format and is latched on the rising edge of BICK. Mode 2 can be used for 16/20 MSB justified formats by zeroing the unused LSBs. In serial mode, when TDM0 bit = "1", the audio interface becomes TDM mode. In TDM256 mode (TDM1 bit = "0", Table 9), the serial data of all DAC (eight channels) is input to the SDTI1 pin. The input data to SDTI2-4 pins is ignored. BICK should be fixed to 256fs. "H" time and "L" time of LRCK should be 1/256fs at least. The serial data is MSB-first, 2's complement format. The input data to SDTI1 pin is latched on the rising edge of BICK. In TDM128 mode (TDM1 bit = "1", Table 10), the serial data of DAC (four channels; L1, R1, L2, R2) is input to the SDTI1 pin. Other four data (L3, R3, L4, R4) is input to the SDTI2. The input data to SDTI3-4 pins is ignored. BICK should be fixed to 128fs. Mode 0 1 2 3 DIF1 0 0 1 1 DIF0 0 1 0 1 SDTI Format 16bit LSB Justified 20bit LSB Justified 24bit MSB Justified 24bit I2S Compatible LRCK H/L H/L H/L L/H BICK 32fs 40fs 48fs 48fs Figure Figure 1 Figure 2 Figure 3 Figure 4
Table 7. Audio Data Formats (Parallel mode) Mode 0 1 2 3 4 TDM1 0 0 0 0 0 TDM0 0 0 0 0 0 DIF2 0 0 0 0 1 DIF1 0 0 1 1 0 DIF0 0 1 0 1 0 SDTI Format 16bit LSB Justified 20bit LSB Justified 24bit MSB Justified 24bit I2S Compatible 24bit LSB Justified LRCK H/L H/L H/L L/H H/L BICK 32fs 40fs 48fs 48fs 48fs Figure Figure 1 Figure 2 Figure 3 Figure 4 Figure 2
Default
Table 8. Audio Data Formats (Serial mode)
LRCK
0 1 10 11 12 13 14 15 0 1 10 11 12 13 14 15 0 1
BICK (32fs) SDTI Mode 0
0
15
1
14
6
14
5
15
4
16
3
17
2
1
31
0
0
15
1
14
6
14
5
15
4
16
3
17
2
1
31
0
15
0
14
1
BICK (64fs) SDTI Mode 0
Don't care 15:MSB, 0:LSB 15 14 0 Don't care 15 14 0
Lch Data
Figure 1. Mode 0 Timing
Rch Data
MS0289-E-00 - 14 -
2004/02
ASAHI KASEI
[AK4359]
LRCK
0 1 8 9 10 11 12 31 0 1 8 9 10 11 12 31 0 1
BICK (64fs) SDTI Mode 1 SDTI Mode 4
Don't care 19:MSB, 0:LSB Don't care 23 22 21 20 19 0 Don't care 23 22 21 20 19 0 19 0 Don't care 19 0
23:MSB, 0:LSB
Lch Data
Figure 2. Mode 1,4 Timing
Rch Data
LRCK
0 1 2 22 23 24 30 31 0 1 2 22 23 24 30 31 0 1
BICK (64fs) SDTI
23 22 23:MSB, 0:LSB 1 0 Don't care 23 22 1 0 Don't care 23 22
Lch Data
Figure 3. Mode 2 Timing
Rch Data
LRCK
0 1 2 3 23 24 25 31 0 1 2 3 23 24 25 31 0 1
BICK (64fs) SDTI
23 22 23:MSB, 0:LSB 1 0 Don't care 23 22 1 0 Don't care 23
Lch Data
Figure 4. Mode 3 Timing
Rch Data
MS0289-E-00 - 15 -
2004/02
ASAHI KASEI
[AK4359]
Mode
5 6 7
TDM1 0 0 0 0 0
TDM0 1 1 1 1 1
DIF2 0 0 0 0 1
DIF1 0 0 1 1 0
DIF0 0 1 0 1 0
SDTI Format N/A N/A 24bit MSB Justified 24bit I2S Compatible 24bit LSB Justified
LRCK
BICK
Figure

256fs 256fs 256fs
Figure 5 Figure 6 Figure 7
Table 9. Audio Data Formats (TDM256 mode)
256 BICK
LRCK BICK(256fs) SDTI1(i)
23 22 0 23 22 0 23 22 0 23 22 0 23 22 0 23 22 0 23 22 0 23 22 0 23 22
L1
32 BICK
R1
32 BICK
L2
32 BICK
R2
32 BICK
L3
32 BICK
R3
32 BICK
L4
32 BICK
R4
32 BICK
Figure 5. Mode 5 Timing
256 BICK
LRCK BICK(256fs) SDTI1(i)
23 0 23 0 23 0 23 0 23 0 23 0 23 0 23 0 23
L1
32 BICK
R1
32 BICK
L2
32 BICK
R2
32 BICK
L3
32 BICK
R3
32 BICK
L4
32 BICK
R4
32 BICK
Figure 6. Mode 6 Timing
256 BICK
LRCK BICK(256fs) SDTI1(i)
23 22 0 23 22 0 23 22 0 23 22 0 23 22 0 23 22 0 23 22 0 23 22 0 23
L1
32 BICK
R1
32 BICK
L2
32 BICK
R2
32 BICK
L3
32 BICK
R3
32 BICK
L4
32 BICK
R4
32 BICK
Figure 7. Mode 7 Timing
MS0289-E-00 - 16 -
2004/02
ASAHI KASEI
[AK4359]
Mode
8 9 10
TDM1 1 1 1 1 1
TDM0 1 1 1 1 1
DIF2 0 0 0 0 1
DIF1 0 0 1 1 0
DIF0 0 1 0 1 0
SDTI Format N/A N/A 24bit MSB Justified 24bit I2S Compatible 24bit LSB Justified
LRCK
BICK
Figure

128fs 128fs 128fs
Figure 8 Figure 9 Figure 10
Table 10. Audio Data Formats (TDM128 mode)
128 BICK
LRCK BICK(128fs) SDTI1(i)
23 22 0 23 22 0 23 22 0 23 22 0 23 22
L1
32 BICK
R1
32 BICK
0 23 22 0 23 22
L2
32 BICK
0 23 22
R2
32 BICK
0 23 22
SDTI2(i)
23 22
L3
32 BICK
R3
32 BICK
L4
32 BICK
R4
32 BICK
Figure 8. Mode 8 Timing
128 BICK
LRCK BICK(128fs) SDTI1(i)
23 22 0 23 22 0 23 22 0 23 22 0 23
L1
32 BICK
R1
32 BICK
0 23 22 0 23 22
L2
32 BICK
0 23 22
R2
32 BICK
0 23
SDTI2(i)
23 22
L3
32 BICK
R3
32 BICK
L4
32 BICK
R4
32 BICK
Figure 9. Mode 9 Timing
128 BICK
LRCK BICK(128fs) SDTI1(i)
23 22 0 23 22 0 23 22 0 23 22 0 19
L1
32 BICK
R1
32 BICK
0 23 22 0 23 22
L2
32 BICK
0 23 22
R2
32 BICK
0 19
SDTI2(i)
23 22
L3
32 BICK
R3
32 BICK
L4
32 BICK
R4
32 BICK
Figure 10. Mode 10 Timing
MS0289-E-00 - 17 -
2004/02
ASAHI KASEI
[AK4359]
De-emphasis Filter
A digital de-emphasis filter is available for 32, 44.1 or 48kHz sampling rates (tc = 50/15s). In case of double speed and quad speed mode, the digital de-emphasis filter is always off. In parallel mode, DEM0-1 pins are valid. DEM1 0 0 1 1 DEM0 0 1 0 1 Mode 44.1kHz OFF 48kHz 32kHz Default
Table 11. De-emphasis Filter Control (Normal Speed Mode)
Output Volume
The AK4359 includes channel independent digital output volumes (ATT) with 256 levels at linear step including MUTE. These volumes are in front of the DAC and can attenuate the input data from 0dB to -48dB and mute. When changing levels, transitions are executed via soft changes; thus no switching noise occurs during these transitions. The transition time of 1 level and all 256 levels is shown in Table 12. The attenuation level is calculated by ATT = 20 log10 (ATT_DATA / 255) [dB] and MUTE at ATT_DATA = "0".
Sampling Speed Normal Speed Mode Double Speed Mode Quad Speed Mode
Transition Time 1 Level 255 to 0 4LRCK 1020LRCK 8LRCK 2040LRCK 16LRCK 4080LRCK
Table 12. ATT Transition time
Zero Detection
When the input data at all channels are continuously zeros for 8192 LRCK cycles, the AK4359 has Zero Detection like Table 13. DZF pin immediately goes to "L" if input data of each channel is not zero after going DZF "H". If RSTN bit is "0", DZF pin goes to "H". DZF pin goes to "L" at 4~5LRCK if input data of each channel is not zero after RSTN bit returns to "1". Zero detect function can be disabled by DZFE bit. In this case, all DZF pins are always "L". When one of PW1-4 bit is set to "0", the input data of DAC that the PW bit is set to "0" should be zero in order to enable zero detection of the other channels. When all PW1-4 bits are set to "0", DZF pin fixes "L". DZFB bit can invert the polarity of DZF pin. DZF Pin DZF1 DZF2 Operations ANDed output of zero detection flag of each channel set to "1" in 0CH register ANDed output of zero detection flag of each channel set to "1" in 0DH register Table 13. DZF pins Operation
MS0289-E-00 - 18 -
2004/02
ASAHI KASEI
[AK4359]
Soft Mute Operation
Soft mute operation is performed at digital domain. When the SMUTE bit goes to "1", the output signal is attenuated by - during ATT_DATAxATT transition time (Table 12) from the current ATT level. When the SMUTE bit is returned to "0", the mute is cancelled and the output attenuation gradually changes to the ATT level during ATT_DATAxATT transition time. If the soft mute is cancelled before attenuating to - after starting the operation, the attenuation is discontinued and returned to ATT level by the same cycle. The soft mute is effective for changing the signal source without stopping the signal transmission.
SMUTE (1) (1) (3)
ATT Level Attenuation
-
GD (2) AOUT (4) 8192/fs GD
DZF pin
Notes: (1) ATT_DATAxATT transition time (Table 12). For example, in Normal Speed Mode, this time is 1020LRCK cycles (1020/fs) at ATT_DATA=255. (2) The analog output corresponding to the digital input has a group delay, GD. (3) If the soft mute is cancelled before attenuating to - after starting the operation, the attenuation is discontinued and returned to ATT level by the same cycle. (4) When the input data at each channel is continuously zeros for 8192 LRCK cycles, DZF pin of each channel goes to "H". DZF pin immediately goes to "L" if input data are not zero after going DZF "H". Figure 11. Soft Mute and Zero Detection (DZFB bit = "0")
MS0289-E-00 - 19 -
2004/02
ASAHI KASEI
[AK4359]
System Reset
The AK4359 should be reset once by bringing RSTB pin = "L" upon power-up. The analog section exits power-down mode by MCLK input and then the digital section exits power-down mode after the internal counter counts MCLK during 4/fs.
Power ON/OFF timing
All DACs are placed in the power-down mode by bringing RSTB pin "L" and the registers are initialized. the analog outputs go to Hi-Z. As some click noise occurs at the edge of RSTB signal, the analog output should be muted externally if the click noise influences system application. Each DAC can be powered down by setting each power-down bit (PW1-4) to "0". In this case, the registers are not initialized and the corresponding analog outputs go to VCOM. As some click noise occurs at the edge of RSTB signal, the analog output should be muted externally if the click noise influences system application.
Power RSTB pin
Internal State
Normal Operation
Reset
(2)
DAC In (Digital)
(2)
"0"data GD (1)
"0"data GD (3)
DAC Out (Analog) Clock In
MCLK,LRCK,SCLK
(3)
(4)
Don't care
Don't care
DZF1/DZF2
(6)
External Mute
(5)
Mute ON
Mute ON
Notes: (1) The analog output corresponding to digital input has the group delay (GD). (2) Analog outputs are floating (Hi -Z) at the power-down mode. (3) Click noise occurs at the edge of RSTB signal. This noise is output even if "0" data is input. (4) The external clocks (MCLK, BICK and LRCK) can be stopped in the power-down mode (RSTB pin = "L"). (5) Please mute the analog output externally if the click noise (3) influence system application. The timing example is shown in this figure. (6) DZF pins are "L" in the power-down mode (RSTB pin = "L"). (DZFB bit = "0") Figure 12. Power-down/up Sequence Example
MS0289-E-00 - 20 -
2004/02
ASAHI KASEI
[AK4359]
Reset Function (RSTN bit)
When RSTN bit = "0", internal circuit of DAC is powered down but the registers are not initialized. The analog outputs go to VCOM voltage and DZF pins go to "H" at DZFB bit = "0". Figure 13 shows the example of reset by RSTN bit. When RSTN bit = "0", pop noise is decreased at no clock state.
RSTN bit
3~4/fs (6) 2~3/fs (6)
Internal RSTN bit Internal State D/A In (Digital) (1) D/A Out (Analog)
Clock In
MCLK,LRCK,BICK
Normal Operation
Digital Block Power-down
Normal Operation
"0" data GD GD
(3)
(2) (4)
Don't care
(3)
(1)
2/fs(5)
DZF
Notes: (1) The analog output corresponding to digital input has the group delay (GD). (2) Analog outputs go to VCOM voltage. (3) Small pop noise occurs at the edges(" ") of the internal timing of RSTN bit. This noise is output even if "0" data is input. (4) The external clocks (MCLK, BICK and LRCK) can be stopped in the reset mode (RSTN bit = "0"). (5) DZF pins go to "H" when the RSTN bit becomes "0", and go to "L" at 2/fs after RSTN bit becomes "1". (6) There is a delay, 3~4/fs from RSTN bit "0" to the internal RSTN bit "0", and 2~3/fs from RSTN bit "1" to the internal RSTN bit "1". Figure 13. Reset Sequence Example (DZFB bit = "0")
MS0289-E-00 - 21 -
2004/02
ASAHI KASEI
[AK4359]
Register Control Interface
The AK4359 controls its functions via registers. 2 types of control mode write internal registers. In the I2C-bus mode, the chip address is determined by the state of the CAD0 pin. In 3-wire mode, the chip address is fixed to "11". RSTB pin = "L" initializes the registers to their default values. Writing "0" to the RSTN bit resets the internal timing circuit, but the register s are not initialized. * The AK4359 does not support the read command. * When the AK4359 is in the power down mode (RSTB bit = "L") or the MCLK is not provided, Writing to control register is inhibited. * When the state of P/S pin is changed, the AK4359 should be reset by RSTB bit = "L". * In serial mode, parallel pin setting is invalid.
Function Double sampling mode at 128/192fs De-emphasis SMUTE Zero Detection 24bit LSB justified format
Parallel mode X O O O X
Serial mode O O O O O
Table 14. Function Table (O: Supported, X: Not supported)
(1) 3-wire Serial Control Mode (I2C pin = "L")
3-wire P interface pins, CSN, CCLK and CDTI, write internal registers. The data on this interface consists of Chip Address (2bits, C1/0; fixed to "11"), Read/Write (1bit; fixed to "1", Write only), Register Address (MSB first, 5bits) and Control Data (MSB first, 8bits). The AK4359 latches the data on the rising edge of CCLK, so data should clocked in on the falling edge. The writing of data becomes valid by the rising edge of CSN. The clock speed of CCLK is 5MHz (max).
CSN
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
CCLK
CDTI
C1 C0 R/W A4 A3 A2 A1 A0 D7 D6 D5 D4 D3 D2 D1 D0
C1-C0: R/W: A4-A0: D7-D0:
Chip Address (Fixed to "11") READ/WRITE (Fixed to "1", Write only) Register Address Control Data
Figure 14. Control I/F Timing
MS0289-E-00 - 22 -
2004/02
ASAHI KASEI
(2) I2C-bus Control Mode (I2C pin = "H")
[AK4359]
The AK4359 supports the fast-mode I2C-bus system (max: 400kHz). Figure 15 shows the data transfer sequence at the I2C-bus mode. All commands are preceded by a START condition. A HIGH to LOW transition on the SDA line while SCL is HIGH indicates a START condition (Figure 19). After the START condition, a slave address is sent. This address is 7 bits long followed by an eighth bit which is a data direction bit (R/W) (Figure 16). The most significant six bits of the slave address are fixed as "001001". The next one bit are CAD0 (device address bit). The bit identify the specific device on the bus. The hard-wired input pin (CAD0 pin) set them. If the slave address match that of the AK4359 and R/W bit is "0", the AK4359 generates the acknowledge and the write operation is executed. If R/W bit is "1", the AK4359 generates the not acknowledge since the AK4359 can be only a slave-receiver. The master must generate the acknowledge-related clock pulse and release the SDA line (HIGH) during the acknowledge clock pulse (Figure 20). The second byte consists of the address for control registers of the AK4359. The format is MSB first, and those most significant 3-bits are fixed to zeros (Figure 17). Those data after the second byte contain control data. The format is MSB first, 8bits (Figure 18). The AK4359 generates an acknowledge after each byte has been received. A data transfer is always terminated by a STOP condition generated by the master. A LOW to HIGH transition on the SDA line while SCL is HIGH defines a STOP condition (Figure 19). The AK4359 is capable of more than one byte write operation by one sequence. After receipt of the third byte, the AK4359 generates an acknowledge, and awaits the next data again. The master can transmit more than one byte instead of terminating the write cycle after the first data byte is transferred. After the receipt of each data, the internal 5bits address counter is incremented by one, and the next data is taken into next address automatically. If the addresses exceed 1FH prior to generating the stop condition, the address counter will "roll over" to 00H and the previous data will be overwritten. The data on the SDA line must be stable during the HIGH period of the clock. The HIGH or LOW state of the data line can only change when the clock signal on the SCL line is LOW (Figure 21) except for the START and the STOP condition.
S T A R T S T O P Sub Address(n) A C K A C K Data(n) A C K Data(n+1) A C K A C K Data(n+x) A C K P
R/W
SDA
S
Slave Address
Figure 15. Data transfer sequence at the I2C-bus mode
0
0
1
0
0
CAD1
CAD0
R/W
(Those CAD1/0 should match with CAD1/0 pins) Figure 16. The first byte
0
0
0
A4
A3
A2
A1
A0
Figure 17. The second byte
D7
D6
D5
D4
D3
D2
D1
D0
Figure 18. Byte structure after the second byte
MS0289-E-00 - 23 -
2004/02
ASAHI KASEI
[AK4359]
SDA
SCL S start condition P stop condition
Figure 19. START and STOP conditions
DATA OUTPUT BY MASTER not acknowledge DATA OUTPUT BY SLAVE(AK4359) acknowledge SCL FROM MASTER S clock pulse for acknowledgement
1
2
8
9
START CONDITION
Figure 20. Acknowledge on the I2 C-bus
SDA
SCL
data line stable; data valid
change of data allowed
Figure 21. Bit transfer on the I2C-bus
MS0289-E-00 - 24 -
2004/02
ASAHI KASEI
[AK4359]
Register Map
Addr 00H 01H 02H 03H 04H 05H 06H 07H 08H 09H 0AH 0BH 0CH 0DH 0EH Register Name Control 1 Control 2 Control 3 LOUT1 ATT Control ROUT1 ATT Control LOUT2 ATT Control ROUT2 ATT Control LOUT3 ATT Control ROUT3 ATT Control LOUT4 ATT Control ROUT4 ATT Control Invert Output Signal DZF1 Control DZF2 Control DEM Control D7 ACKS 0 PW4 ATT7 ATT7 ATT7 ATT7 ATT7 ATT7 ATT7 ATT7 INVL1 L1 L1 0 D6 TDM1 0 PW3 ATT6 ATT6 ATT6 ATT6 ATT6 ATT6 ATT6 ATT6 INVR1 R1 R1 0 D5 TDM0 SLOW PW2 ATT5 ATT5 ATT5 ATT5 ATT5 ATT5 ATT5 ATT5 INVL2 L2 L2 0 D4 DIF2 DFS1 0 ATT4 ATT4 ATT4 ATT4 ATT4 ATT4 ATT4 ATT4 INVR2 R2 R2 0 D3 DIF1 DFS0 0 ATT3 ATT3 ATT3 ATT3 ATT3 ATT3 ATT3 ATT3 INVL3 L3 L3 DEMA D2 DIF0 DEM1 DZFB ATT2 ATT2 ATT2 ATT2 ATT2 ATT2 ATT2 ATT2 INVR3 R3 R3 DEMB D1 PW1 DEM0 PW1 ATT1 ATT1 ATT1 ATT1 ATT1 ATT1 ATT1 ATT1 INVL4 L4 L4 DEMC D0 RSTN SMUTE 0 ATT0 ATT0 ATT0 ATT0 ATT0 ATT0 ATT0 ATT0 INVR4 R4 R4 DEMD
Note: For addresses from 0FH to 1FH, data must not be written. When RSTB pin goes to "L", the registers are initialized to their default values. When RSTN bit goes to "0", the only internal timing is reset, and the registers are not initialized to their default values. All data can be written to the registers even if PW1-4 bit or RSTN bit is "0".
Register Definitions
Addr 00H Register Name Control 1 Default D7 ACKS 1 D6 TDM1 0 D5 TDM0 0 D4 DIF2 0 D3 DIF1 1 D2 DIF0 0 D1 PW1 1 D0 RSTN 1
RSTN: Internal timing reset 0: Reset. All DZF pins go to "H" and any registers are not initialized. 1: Normal operation When MCLK frequency or DFS changes, the AK4359 should be reset by RSTB pin or RSTN bit. PW1: Power-down control (0: Power-down, 1: Power-up) PW1: Power down control of DAC1 This bit is duplicated into D1 of 02H. DIF2-0: Audio data interface modes (See Table 8, Table 9, Table 10) Initial: "010", SLOW: Slow Roll-off Filter Enable 0: Sharp Roll-off Filter 1: Slow Roll-off Filter
MS0289-E-00 - 25 -
2004/02
ASAHI KASEI
[AK4359]
TDM0-1: TDM Mode Select Mode Normal TDM256 TDM128 TDM1 0 0 1 TDM0 0 1 1 BICK 32fs 256fs fixed 128fs fixed SDTI 1-4 1 1-2 Sampling Speed Normal, Double, Quad Speed Normal Speed Normal, Double Speed
ACKS: Master Clock Frequency Auto Setting Mode Enable 0: Disable, Manual Setting Mode 1: Enable, Auto Setting Mode Master clock frequency is detected automatically at ACKS bit "1". In this case, the setting of DFS1-0 bits are ignored. When this bit is "0", DFS1-0 bits set the sampling speed mode. Addr 01H Register Name Control 2 Default D7 0 0 D6 0 0 D5 SLOW 0 D4 DFS1 0 D3 DFS0 0 D2 DEM1 0 D1 DEM0 1 D0 SMUTE 0
SMUTE: Soft Mute Enable 0: Normal operation 1: DAC outputs soft-muted DEM1-0: De-emphasis Response (See Table 11) Initial: "01", OFF DFS1-0: Sampling speed control (See Table 1) 00: Normal speed 01: Double speed 10: Quad speed When changing between Normal/Double Speed Mode and Quad Speed Mode, some click noise occurs. SLOW: Slow Roll-off Filter Enable 0: Sharp Roll-off Filter 1: Slow Roll-off Filter Adr 02H Register Name
Speed & Control Power Down
D7 PW4 1
D6 PW3 1
D5 PW2 1
D4 0 0
D3 0 0
D2 DZFB 0
D1 PW1 1
D0 0 0
Default
PW1: Power-down control (0: Power-down, 1: Power-up) PW1: Power down control of DAC1 This bit is duplicated into D1 of 00H. DZFB: Inverting Enable of DZF 0: DZF goes "H" at Zero Detection 1: DZF goes "L" at Zero Detection PW4-2: Power-down control (0: Power-down, 1: Power-up) PW2: Power down control of DAC2 PW3: Power down control of DAC3 PW4: Power down control of DAC4 All sections are powered-down by PW1=PW2=PW3=PW4=0.
MS0289-E-00 - 26 -
2004/02
ASAHI KASEI
[AK4359]
Addr 03H 04H 05H 06H 07H 08H 09H 0AH
Register Name LOUT1 ATT Control ROUT1 ATT Control LOUT2 ATT Control ROUT2 ATT Control LOUT3 ATT Control ROUT3 ATT Control LOUT4 ATT Control ROUT4 ATT Control Default
D7 ATT7 ATT7 ATT7 ATT7 ATT7 ATT7 ATT7 ATT7 1
D6 ATT6 ATT6 ATT6 ATT6 ATT6 ATT6 ATT6 ATT6 1
D5 ATT5 ATT5 ATT5 ATT5 ATT5 ATT5 ATT5 ATT5 1
D4 ATT4 ATT4 ATT4 ATT4 ATT4 ATT4 ATT4 ATT4 1
D3 ATT3 ATT3 ATT3 ATT3 ATT3 ATT3 ATT3 ATT3 1
D2 ATT2 ATT2 ATT2 ATT2 ATT2 ATT2 ATT2 ATT2 1
D1 ATT1 ATT1 ATT1 ATT1 ATT1 ATT1 ATT1 ATT1 1
D0 ATT0 ATT0 ATT0 ATT0 ATT0 ATT0 ATT0 ATT0 1
ATT = 20 log10 (ATT_DATA / 255) [dB] 00H: Mute Addr 0BH Register Name Invert Output Signal Default D7 INVL1 0 D6 INVR1 0 D5 INVL2 0 D4 INVR2 0 D3 INVL3 0 D2 INVR3 0 D1 INVL4 0 D0 INVR4 0
INVL4-1, INVR4-1: Inverting Output Polarity 0: Normal Output 1: Inverted Output Addr 0CH 0DH Register Name DZF1 Control DZF2 Control Default D7 L1 L1 0 D6 R1 R1 0 D5 L2 L2 0 D4 R2 R2 0 D3 L3 L3 0 D2 R3 R3 0 D1 L4 L4 0 D0 R4 R4 0
L1-4, R1-4: Zero Detect Flag Enable Bit for DZF1/2 pins 0: Disable 1: Enable Addr 0EH Register Name DEM Control Default D7 0 0 D6 0 0 D5 0 0 D4 0 0 D3 DEMA 0 D2 DEMB 0 D1 DEMC 0 D0 DEMD 0
DEMA-D: De-emphasis Enable bit of DAC1/2/3/4 0: Disable 1: Enable
MS0289-E-00 - 27 -
2004/02
ASAHI KASEI
[AK4359]
SYSTEM DESIGN
Figure 22 and 23 shows the system connection diagram. An evaluation board (AKD4359) is available which demonstrates application circuits, the optimum layout, power supply arrangements and measurement results.
Master Clock 64fs 24bit Audio Data fs Res et Microcontroller 24bit Audio Data 24bit Audio Data 24bit Audio Data Microcontroller
10u + 0.1u
1
MCLK
DZF1
30
2 3 4 5 6 7 8 9 10 11 12 13 14 15
BICK SDTI1 LRCK PDN SMUTE ACKS DIF0 SDTI2 SDTI3 SDTI4 DIF1 DEM0 DVDD DVSS
DZF2 AVDD AVSS VCOM
29 28 27 26 25 24 23 22 21 20 19 18 17 16
0.1u 10u +
Analog 5V
+ 0.1u 10u
MUTE MUTE
AK4359
LOUT1 ROUT1 P/S LOUT2 ROUT2 LOUT3 ROUT3 LOUT4 ROUT4 DEM1
L1ch Out R1ch Out
MUTE MUTE MUTE MUTE MUTE MUTE
L2ch Out R2ch Out L3ch Out R3ch Out L4ch Out R4ch Out
Micro-controller Digital 5V
Digital Ground
Analog Ground
Figure 22. Typical Connection Diagram (Parallel Mode)
MS0289-E-00 - 28 -
2004/02
ASAHI KASEI
[AK4359]
Master Clock 64fs 24bit Audio Data fs Res et Microcontroller 24bit Audio Data 24bit Audio Data 24bit Audio Data Microcontroller
10u + 0.1u
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
MCLK BICK SDTI1 LRCK PDN CSN CCLK CDTI SDTI2 SDTI3 SDTI4 DIF1 DEM0 DVDD DVSS
DZF1 DZF2 AVDD AVSS VCOM
30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
MUTE MUTE MUTE MUTE MUTE MUTE
0.1u 10u +
Analog 5V
+ 0.1u 10u
MUTE MUTE
AK4359
LOUT1 ROUT1 P/S LOUT2 ROUT2 LOUT3 ROUT3 LOUT4 ROUT4 I2C
L1ch Out R1ch Out
L2ch Out R2ch Out L3ch Out R3ch Out L4ch Out R4ch Out
Digital 5V
Digital Ground
Analog Ground
Figure 23. Typical Connection Diagram (3-wire Serial Mode) Notes: - LRCK = fs, BICK = 64fs. - When AOUT drives some capacitive load, some resistor should be added in series between AOUT and capacitive load. - All input pins except pull-up pin should not be left floating.
MS0289-E-00 - 29 -
2004/02
ASAHI KASEI
[AK4359]
Digital Ground
Analog Ground
1 2 3 4 MCLK BICK SDTI1 LRCK PDN SMUTE/CSN/CAD0 ACKS/CCLK/CSL DFS0/CDT/SDA SDTI2 SDTI3 SDTI4 DIF1 DEM0 DVDD DVSS DZF1 DZF2 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
AK4359
AVDD AVSS VCOM LOUT1 ROUT1 P/S LOUT2 ROUT2 LOUT3 ROUT3 LOUT4 ROUT4 DEM1/I2C
System Controller
5 6 7 8 9 10 11 12 13 14 15
Figure 24. Ground Layout AVSS and DVSS must be connected to the same analog ground plane.
1. Grounding and Power Supply Decoupling
AVDD and DVDD are usually supplied from analog supply in system and should be separated from system digital supply. Alternatively if AVDD and DVDD are supplied separately, the power up sequence is not critical. AVSS and DVSS of the AK4359 must be connected to analog ground plane. System analog ground and digital ground should be connected together near to where the supplies are brought onto the printed circuit board. Decoupling capacitor, especially 0.1F ceramic capacitor for high frequency should be placed as near to AVDD and DVDD as possible.
2. Voltage Reference
VREFH sets the analog output range. VREFH pin is normally connected to AVDD with a 0.1F ceramic capacitor. All signals, especially clocks, should be kept away from the VREFH pin in order to avoid unwanted coupling into the AK4359.
3. Analog Outputs
The analog outputs are single-ended and centered around the VCOM voltage. The output signal range is typically 3.40Vpp (typ@VDD=5V). The phase of the analog outputs can be inverted channel independently by INVL/INVR bits. The internal switched-capacitor filter and continuous-time filter attenuate the noise generated by the delta-sigma modulator beyond the audio passband. The input data format is 2's complement. The output voltage is a positive full scale for 7FFFFFH (@24bit) and a negative full scale for 800000H (@24bit). The ideal output is VCOM voltage for 000000H (@24bit). DC offsets on analog outputs are eliminated by AC coupling since analog outputs have DC offsets of VCOM + a few mV.
MS0289-E-00 - 30 -
2004/02
ASAHI KASEI
[AK4359]
PACKAGE
30pin VSOP
30pin VSOP (Unit: mm)
*9.70.1 0.3 30 1.5MAX
16 A 7.60.2 0.15 +0.10 -0.05 Detail A 0.450.2
1 0.220.1
15 0.65
0.12 M
1.20.10
0.08
NOTE: Dimension "*" does not include mold flash.
Package & Lead frame material
Package molding compound: Lead frame material: Lead frame surface treatment: Epoxy Cu Solder (Pb free) plate
MS0289-E-00 - 31 -
0.10 -0.05
+0.10
5.60.1
2004/02
ASAHI KASEI
[AK4359]
MARKING
AKM AK4359VF XXXBYYYYC
XXXBYYYYC
Date code identifier
XXXB : Lot number (X : Digit number, B : Alpha character) YYYYC : Assembly date (Y : Digit number, C : Alpha character)
IMPORTANT NOTICE * These products and their specif ications are subject to change without notice. Before considering any use or application, consult the Asahi Kasei Microsystems Co., Ltd. (AKM) sales off ice or authorized distributor concerning their current status. * AKM assumes no liability for infringement of any patent, intellectual property, or other right in the application or use of any information contained herein. * Any export of these products, or devices or systems containing them, may require an export license or other official approval under the law and regulations of the country of export pertaining to customs and tariffs, currency exchange, or strategic materials. * AKM products are neither intended nor authorized for use as critical components in any safety, life support, or other hazard related device or system, and AKM assumes no responsibility relating to any such use, except with the express written consent of the Representative Director of AKM. As used here: (a) A hazard related device or system is one designed or intended for life support or maintenance of safety or for applications in medicine, aerospace, nuclear energy, or other fields, in which its failure to function or perform may reasonably be expected to result in loss of lif e or in significant injury or damage to person or property. (b) A critical component is one whose failure to function or perform may reasonably be expected to result, whether directly or indirectly, in the loss of the saf ety or effectiveness of the device or system containing it, and which must therefore meet very high standards of performance and reliability. * It is the responsibility of the buyer or distributor of an AKM product who distributes, disposes of, or otherwise places the product with a third party to notify that party in advance of the above content and conditions, and the buyer or distributor agrees to assume any and all responsibility and liability for and hold AKM harmless from any and all claims arising from the use of said product in the absence of such notification.
MS0289-E-00 - 32 -
2004/02

▲Up To Search▲

Price & Availability of AK4359

	To Download AK4359 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .